介紹

Summary

圈圓機是生廠家具板材圈圓的公共裝配，為三滾式圈圓機。其格局公正無私、專業調劑友盒、生廠打球高、使用簡單，并可在圈圓tcp連接中圈壓出對焊接工藝口處兩直邊，為下兩個工藝程序對焊創下突出的根本就, 材料板厚不跨越式4.5mm。This coiler machine is special equipment that is used for steel plate coiling. It has reasonable structure with 3 rollers type design, convenient adjustment, high efficiency and simple operation, and also it can press out straight flange on the two sides of welding joint in the coiling process to lay a good foundation for the next working procedure butt welding except the material exceed 4.5mm.

該輔助裝備符合復印和壓平的兩重功較。此中復印代替在輪輞板料毛培房上壓出所需注意的標簽，如輪輞的規格參數、材質、產地服務商、產地年份等，壓平則是為在將來電弧焊接。This is special equipment for rim production, which has dual function of stamping and flattening. The stamper of it is used to press the needed marks on the rim band, including specification, model, manufacturer, production date etc. It flattens weld joint for the following welding operation.

第一手工加工生產工序是：自主放料à打印機à圈圓à壓平對接焊縫Automatic operating for feeding-stamping-coiling-flattening weld joint

轉備平面布置簡單

Equipment Structure Introduction

加工中心由主動性給料單位、打字單位、卷圓機和壓平單位四部分搭建。The equipment includes four parts：automatically feeder, stamper, coiler and flattening device.

上料臺由形鋼悍接而成，上置鋁斷橋鋁材上料之架，用以上料被動送進。The feeding platform is welded with structure steel, on which place aluminous feeding rack for material automatically feeding.

彩印機由水平兩印壓延機造成，彩印用的字頭裝鄙人壓延機，可可根據需注意很友盒的更調。當送料機進印壓延機內時，不斷進取印壓延機起頭運轉，將鋼字按序印壓在板料上，并將印壓好的板料收到，隨著印壓延機沿途歷程氣門主動權規復原位，是為了切合區分板厚的請求，兩印壓延機的細縫可能手工藝廚衛。The stamper is made of upper and lower roller. The marking unit is installed on the lower roller, which is easy to change by requirement. When the steel card is feed into the press-stamping roller, push roller to make it roll and stamp steel letters on the band one by one then push out the finished band, the press-stamping roller will back to the home position by the cylinder. The gap between two rollers can be adjusted manually to meet different band thickness.

根本規格

Main Parameter

輔助裝備型號規格	Model Number	Номер модели	JYJ-600-AH
數據規格	material thickness	Толщина обода	≤4.5mm
工件的屏幕寬度匹配	Rim Width	Ширина обода	≤320mm
半徑面積	Rim Diameter Range	Диаметр обода	300mm~500mm
所在熱效率	input capacity	Общая мощность	14KW

手工藝亮點

這個機器的不間斷標準系統由可思維邏輯合理器PLC、打戰器、定頻器、電機驅動器標準系統、電氣自動化和各大判斷感應器器購成。合理器尊重斯耐德開關M218編，斯耐德開關M218 PLC體積計算小、頻率快、技術專業化，滿足串口通信設備就可以，攻效強，靠受得了高朝。

This equipment’s electrical system consists of PLC (Programmable Logic Control), contactor, frequency converter, servo system, motor and different kinds of detecting sensor. The controller is used series M218 of Schneider, which is small, fast, reliable, standardizing and has ability of serial communication.

裝備的操縱形式

Equipment’s Operation Mode

臺式主機有主動權和手動兩類重任體例，它是經過了工作扳動“主動權/手動”停止工作區分。The main machine has two kinds of working mode--- auto and manual, which can choose by turning the “auto/manual” button.

1手動形式

Manual Mode

零丁使用機箱裝置的每臺強化措施，用于使用工作人員的化合物調濟和裝置保護措施。Operate every single action of main machine to make operator easy to adjust and maintain equipment.

2主動形式

Auto Mode

表明固定性的西式關閉主動地命輪，控制者只目前送料、開料便可。Work circularly and automatically by the set process, the operator only needs to load and unload material.

聯動/單動

single/linkage

服務器和自主的上料機構造有三級聯調和單動哪幾種成就體例，經過具體步驟扳動“三級聯調/單動”中斷隨意挑選。There are two working mode for main machine and automatically feeding device--- single and linkage, which can be chosen by turning “linkage/single” button.

單動形式

single mode

在分手后表現形式下，一旦網頁打印和卷圓機、壓平機分手后天道輪回，不含有放料結構。Under the auto mode can only circularly work stamper and flattener without feeding device.

聯動形式

linkage mode

在分手后主要形式下，在彩印和卷圓機分手后輪回轉世中豐富分手后上料機功用，建筑工人只需將料垛加在放卷小車子便可。Under the auto mode, add automatically feeding function to automatical circle of stamping and coiler, worker only need to put material on the feeding dolly.

說話切換

Language

鍵后“口才切回”后顯露如上圖所述，進行英漢雙文切回。Click “language” to get into the interface like above picture, where can choose language between Chinese and English.